Quality hydraulic seal factory manufacturer: Without the pressure pushing them apart the two seal faces would be in full contact, this is known as dry running and would lead to rapid seal failure. Without the process pressure (and the force of the springs) pushing the faces together the seal faces would separate too far, and allow fluid to leak out. Mechanical seal engineering focuses on increasing the longevity of the primary seal faces by ensuring a high quality of lubricating fluid, and by selecting appropriate seal face materials for the process being pumped. When we talk about leakage we are referring to visible leakage of the seal. This is because as detailed above, a very thin fluid film holds the two seal faces apart from each other. By maintaining a micro-gap a leak path is created making it impossible for a mechanical seal to be totally leak free. What we can say, however, is that unlike gland packing, the amount of leakage on a mechanical seal should be so low as to be visually undetectable. See even more details on https://www.dmsseals.com/spring-seals.
Every other leak path within the mechanical seal is blocked with the use off a gasket, o-ring, wedge (Rubber, PTFE or Flexible Graphite). The other key aspect of a mechanical pump seal is how to maintain the seal. Springs (single or multiple), a metal bellows or just compressed elastomers are used to provide the needed energy to keep pressing the seal faces together. The load the seal faces receive are engineered into the design of the seal. The choice of what is the best depends on the temperature, and nature of what is being sealed (viscosity, abrasiveness, weight (is it a slurry?)). Cartridge Seals are pre-assembled package of mechanical seal components making installation much easier with fewer points for potential mechanical pump seal installation errors to occur. Mechanical seals occasionally require a seal pot to provide a buffer fluid for your double cartridge seals. Seal pots can not only provide a lubricating buffer, but they can also heat or cool the barrier fluid they contain.
Due to the volume and weight limitations of the system, it is impossible to install an ideal filtration and cooling system. High temperature, high pressure, and high speed cause the hydraulic oil to deteriorate easily, and the mechanical parts are also prone to erosion and stains. There are many stains and impurities in hydraulic oil, but it cannot be thoroughly filtered, which is the aspect of endogenous stains. All kinds of dust in the working environment may be very large, and it will inevitably enter the hydraulic system in multiple ways, causing oil pollution, which is an external stain. Therefore, the sealing system is required to be resistant to stains.
The radial force of our rotary seals on the shaft and the distribution is very reasonable. It can achieve the optimal “critical oil film thickness” working condition and always maintain critical lubrication. We guarantee that our rotary seal can help the machine get the sharpest “peak” pressure distribution with the least radial force, providing the best sealing effect. The bearing seal is designed by DMS SEALS to isolate the moving metal part, guiding the piston and piston rod of the hydraulic cylinder to move in a certain direction and it can help withstand lateral loads. It helps prevent any direct contact between the piston metal and the cylinder metal and prevents strain and seal damage on the inner surface of the cylinder.
The gasket made by DMS SEALS is uniquely mechanical and thermally stable and it has excellent oxidation resistance. Compared with other thermoplastics, it can be applied to components such as valves and bushings, with higher wear resistance, higher mechanical properties and thermal fatigue resistance. At the same time, it has excellent oil resistance (alkane oil), heat resistance, water resistance, aging resistance, air tightness and excellent adhesion. It is commonly used in media such as water, oil, and natural gas.
Our piston seals are designed to provide excellent leak control. We guarantee that it can perfectly meet the user’s requirements for low friction, compactness, precise configuration and simple installation. It is designed for fluid power applications. It is made of compound materials with high performance, which guarantees excellent wear resistance and excellent extrusion resistance for the seal. It is designed to be suitable for almost all fluid media and is highly resistant to oxidation and corrosion. It has excellent dynamic and static sealing performance and can even work under dusty industrial environments. Moreover, it has strong adaptability to various working conditions and can adapt to a fast, high-pressure working environment. At the same time, it has unparalleled performance in extreme temperature environments.
Influence of flange form: Different flange forms require different gaskets. Smooth-faced flanges are generally only used for low pressure, with soft thin gaskets; under high pressure, if the strength of the flange is sufficient, smooth-faced flanges can also be used, but thick soft gaskets should be used, or inner belt reinforcement should be used. Wound gasket for ring or reinforcement ring. In this case, metal gaskets are also not suitable, because the required pressing force is too large, resulting in large deformation of the bolts, making the flange difficult to seal. If a metal gasket is to be used, the smooth surface should be reduced to reduce the contact area with the gasket. In this way, under the condition of the same bolt tension, the compressive stress of the reduced narrow smooth surface will increase.
The guide belt is a belt-shaped member that guides the moving parts. Its main function is to guide. In order to realize the function of guidance, it must support the guided member, and guide and correct its motion trajectory. In order to realize the guiding function well, it also requires isolation, shock absorption and noise reduction of the guiding parts. Guide belts are mainly used in oil cylinders and cylinders. Due to their excellent performance, they are also widely used in other motion mechanisms. Find more details at dmsseals.com.
DMS Seals is a scientific and technical mechanical seal manufacturer and oil seal supplier specializing in seal production, sealing material development, and the conception of sealing solutions for special working conditions. We have 120 employees, including 70 senior technicians. DMS Seals has a number of invention patents and leading production processes. The R&D team is able to design and develop Rubber Seal & Hydraulic Seals for various mechanical sealing systems under complex conditions. We have already passed the certification of ISO 9001 and TS 16949.